13549213581 肖生

 

TECAPEEK® PVX

 

Polyetheretherketone

 

Ensinger Inc.

 

Technical Data

 

Product Description

 

TECAPEEK® PVX is an ultra high performance bearing material that incorporates the properties of a premium polymetric matrix material with optimum levels of specific wear enhancing additives. This formulation raises the continuous use temperature by approximately 40°F and increases the limiting PV while maintaining excellent chemical resistance. When used as a non-metallic bearing, TECAPEEK® PVX offers a superb range of tribiological performance. It is designed to run at high loads and speeds, in hostile environments, either dry or lubricated.

 

TECAPEEK™ PVX'S exceptional properties make it an ideal material for bearing surfaces in the most demanding applications and in the harshest conditions. Industrial, automotive, marine, nuclear, petroleum and aerospace industry applications realize great benefits from its use.

 

General

 

Material Status • Commercial: Active

Literature 1 • Technical Datasheet (English)

Availability • North America

Additive • Unspecified Additive

Features • Good Chemical Resistance • Good Weather Resistance • Low Smoke Emission

• Good Wear Resistance • High Heat Resistance • Radiation (Gamma) Resistant

Uses • Aerospace Applications • Industrial Applications • Nuclear Power Applications

• Automotive Applications • Marine Applications • Oil/Gas Applications

Forms • Plate • Rod

 

Physical Nominal Value (English) Nominal Value (SI) Test Method

Specific Gravity 1.48 1.48 g/cm³ ASTM D792

Mechanical Nominal Value (English) Nominal Value (SI) Test Method

Tensile Strength (Yield, 73°F (23°C)) 17300 psi 119 MPa ASTM D638

Tensile Elongation (Break, 73°F (23°C)) 2.5 % 2.5 % ASTM D638

Flexural Modulus - Tangent (73°F (23°C)) 1.40E+6 psi 9650 MPa ASTM D790

Flexural Strength (73°F (23°C)) 30000 psi 207 MPa ASTM D790

Compressive Strength (73°F (23°C)) 22000 psi 152 MPa ASTM D695

Coefficient of Friction 3 0.19 to 0.21 0.19 to 0.21 ASTM D1894

Wear Rate 0.00125 to 0.00150 in/min 0.00125 to 0.00150 in/min

Impact Nominal Value (English) Nominal Value (SI) Test Method

Notched Izod Impact (73°F (23°C)) 3.3 ft•lb/in 170 J/m ASTM D256

Hardness Nominal Value (English) Nominal Value (SI) Test Method

Rockwell Hardness (M-Scale) 85 85 ASTM D785

Thermal Nominal Value (English) Nominal Value (SI) Test Method

Deflection Temperature Under Load ASTM D648

264 psi (1.8 MPa), Unannealed, 0.250 in (6.35 530 °F 277 °C

mm)

Continuous Use Temperature 500 °F 260 °C

Melting Temperature 633 °F 334 °C

CLTE - Flow 3.1E-6 in/in/°F 5.6E-6 cm/cm/°C ASTM D696

Electrical Nominal Value (English) Nominal Value (SI) Test Method

Surface Resistivity 1.0E+5 to 1.0E+8 ohms 1.0E+5 to 1.0E+8 ohms ASTM D257

Volume Resistivity (73°F (23°C)) 1.4E+5 ohms•cm 1.4E+5 ohms•cm ASTM D257

Flammability Nominal Value (English) Nominal Value (SI) Test Method

Flame Rating V-0 V-0 UL 94

Additional Information Nominal Value (English) Nominal Value (SI)

Limiting Pressure Velocity 25000 to 30000 25000 to 30000

Data based on injection molded samples.

 

 

 

 

 

聚醚醚酮,PEEK TECAPEEK® PVX是东莞市双帮塑胶原料有限公司常年销售的塑料，因为塑料价格行情每天都有新变化前天的报价不等于今天的报价。本公司销售的所有原料保证是原厂原包,随料可以提供生产厂商提供的物性表、SGS报告，COA原料出厂报告,REACH报告,SVHC报告,UL黄卡,提供原料注塑加工工程中可能出现的各种异常现象解决方法，塑料牌号太多，本网站没有提供的本公司也有代理，详情请咨询本公司相关业务人员0769-87795123 

13549213581 肖生