|
聚醚醚酮,PEEK TRIBOCOMP® PEEK TS9东莞市双帮塑胶原料有限公司常年销售的塑料，因为塑料价格行情每天都有新变化前天的报价不等于今天的报价。本公司销售的所有原料保证是原厂原包,随料可以提供生产厂商提供的物性表、SGS报告，COA原料出厂报告,REACH报告,SVHC报告,UL黄卡,提供原料注塑加工工程中可能出现的各种异常现象解决方法，塑料牌号太多，本网站没有提供的本公司也有代理，详情请咨询本公司相关业务人员0769-87795123
13549213581 肖生
TRIBOCOMP® PEEK TS9
Polyetheretherketone
EPIC Polymers
Technical Data
Product Description
TRIBOCOMP® PEEK TS9 is a Polyetheretherketone (PEEK) product. It is available in Europe.
General
Material Status • Commercial: Active
Literature 1 • Technical Datasheet (English)
Search for UL Yellow Card • EPIC Polymers
Availability • Europe
Forms • Pellets
Physical Nominal Value (English) Nominal Value (SI) Test Method
Density 1.40 g/cm³ 1.40 g/cm³ ISO 1183
Molding Shrinkage - Flow 1.1 % 1.1 % ISO 294-4
Water Absorption ISO 62
Equilibrium, 73°F (23°C), 50% RH 0.20 % 0.20 %
Mechanical Nominal Value (English) Nominal Value (SI) Test Method
Tensile Modulus (73°F (23°C)) 638000 psi 4400 MPa ISO 527-2
Tensile Stress (Yield, 73°F (23°C)) 10200 psi 70.0 MPa ISO 527-2
Tensile Strain (Break) > 5.0 % > 5.0 % ISO 527-2
Flexural Modulus (73°F (23°C)) 609000 psi 4200 MPa ISO 178
Flexural Stress (73°F (23°C)) 14500 psi 100 MPa ISO 178
Coefficient of Friction ASTM D3702
Dynamic 0.14 0.14
Static 0.12 0.12
Wear Factor 8.00 8.00 ASTM D3702
Impact Nominal Value (English) Nominal Value (SI) Test Method
Charpy Notched Impact Strength (73°F (23°C)) 3.3 ft•lb/in² 7.0 kJ/m² ISO 179
Charpy Unnotched Impact Strength ISO 179
73°F (23°C) 31 ft•lb/in² 65 kJ/m²
Thermal Nominal Value (English) Nominal Value (SI) Test Method
Heat Deflection Temperature
66 psi (0.45 MPa), Unannealed 572 °F 300 °C ISO 75-2/B
264 psi (1.8 MPa), Unannealed 347 °F 175 °C ISO 75-2/A
CLTE - Flow (73°F (23°C)) 2.5E-5 in/in/°F 4.5E-5 cm/cm/°C ISO 7991
Thermal Conductivity 3.5 Btu•in/hr/ft²/°F 0.50 W/m/K ISO 22007
Electrical Nominal Value (English) Nominal Value (SI) Test Method
Surface Resistivity 1.0E+15 ohms 1.0E+15 ohms ASTM D257
Electric Strength (0.0787 in (2.00 mm)) 640 V/mil 25 kV/mm IEC 60243-1
Comparative Tracking Index 125 V 125 V IEC 60112
Additional Information
The value listed as Molding Shrinkage ISO 294-4, was tested in accordance with S.O.P. methods.
Injection Nominal Value (English) Nominal Value (SI)
Drying Temperature 302 °F 150 °C
Drying Time 4.0 hr 4.0 hr
Suggested Max Moisture 0.050 % 0.050 %
Rear Temperature 644 to 680 °F 340 to 360 °C
Middle Temperature 680 to 716 °F 360 to 380 °C
Front Temperature 716 to 734 °F 380 to 390 °C
Nozzle Temperature 716 to 734 °F 380 to 390 °C
Mold Temperature 320 to 392 °F 160 to 200 °C
聚醚醚酮,PEEK TRIBOCOMP® PEEK TS9是东莞市双帮塑胶原料有限公司常年销售的塑料，因为塑料价格行情每天都有新变化前天的报价不等于今天的报价。本公司销售的所有原料保证是原厂原包,随料可以提供生产厂商提供的物性表、SGS报告，COA原料出厂报告,REACH报告,SVHC报告,UL黄卡,提供原料注塑加工工程中可能出现的各种异常现象解决方法，塑料牌号太多，本网站没有提供的本公司也有代理，详情请咨询本公司相关业务人员0769-87795123
13549213581 肖生
|
